(Polarity of the input connection is not important.) If your gauge came with a counter display and battery, disconnectĬoupler lever (for use with HOBO Waterproof Shuttle) Important: Do not cover the optical communication window in the logger (shown in diagram above) with a label or sticker as that may interfere with the communications with the base station or shuttle.Ĭonnecting to a Tipping-Bucket Rain Gauge The loggers black and white input wires can be connected directly to the relay output of most tipping-bucket rain gauges.
HOBO PENDANT LIGHT LOGGER MANUAL SOFTWARE
Refer to the software users guide for complete details on launching, reading out, and viewing data from the logger. You can read out the logger or check its status while it continues to log, stop it manually with the software, or let it record data until the memory is full. Use the logger software to set up the alarms, launch, and read out the logger. If the logger has never been connected to the computerīefore, it may take a few seconds for the new hardware to be detected.ĥ. The coupler lever to put the shuttle into base station mode. If you are using the HOBO Waterproof Shuttle, briefly press For BASE-U-1, make sure that the logger is inserted in the end of the coupler that has the magnet, and that the ridges on the base station and logger are aligned with the grooves in the coupler.įor BASE-U-4 or the HOBO Waterproof Shuttle, firmly insert the optical end of the base station into the D-shaped end of the coupler, and make sure that the ridge on the logger is aligned with the groove in the coupler.ģ. Insert the logger and the base station into the coupler, as shown in the following diagrams. Plug the USB connector on the base station into an available USB port on your computer.Ģ. If possible, avoid connecting at temperatures below 0C (32F) or above 50C (122F).ġ. Optic USB Base Station (BASE-U-4) or HOBO Waterproof Shuttle (U-DTW-1) coupler (COUPLER2A) HOBOware 2.2 or later Pendant Optic USB Base Station & Coupler (BASE-U-1) HOBOware 2.1 or later OR HOBO Pendant Event Data Logger (UA-003) ManualĬonnecting the Logger to a Computer The HOBO Pendant logger requires either of the following to connect to the computer: (BASE-U-4) or HOBO Waterproof Shuttle (U-DTW-1) & Coupler (COUPLER2-A) Station & Coupler (BASE-U-1) Optic USB Base Station Required Items: HOBOware 2.x or later USB cable (included with The CE Marking identifies this product as complying with all relevant directives in the European Union (EU). Materials Polypropylene case stainless steel screws Buna-N o-ring PVC cable insulationĭimensions 71 x 33 x 23 mm (2.8 x 1.3 x 0.9 inches) 1.8 m (6 ft) cable Time Accuracy 1 minute per month at 25C (77F), see Plot BĮnvironmental Rating Tested to NEMA 6 and IP67 suitable for deployment outdoorsĭrop Specification 1.5 m (5 ft) onto concreteĪvailable for temperature only at additional charge temperature range -20 to 70C (-4 to 158F)īattery CR-2032 3V lithium battery 1 year typical use Response Time Airflow of 2 m/s (4.4 mph): 10 minutes, typical to 90% Resolution 0.14C at 25C (0.25F at 77F), see Plot A A solar radiation shield is required for accurate temperature measurements in sunlight. User Connection 24 AWG, 2 leads: white (+), black (-) Maximum Input Voltage Battery voltage + 0.3 V The logger will work with normally closed switches, but battery life will be compromised. For maximum battery life, the event input should be used with its preferred switch type. Minimum Pulse Width 1 ms (hardware debounce)Įdge Detection Falling edge, contact closure, or Schmitt-trigger buffer
![hobo pendant light logger manual hobo pendant light logger manual](https://www.onsetcomp.com/files/styles/image_widget_large/public/product-images/H06-002-02.jpg)
The logger uses a coupler and optical base station with USB interface for launching and data readout by a computer.Įvent Sensor Two-wire interface suitable for measuring mechanical and electrical contact closures It is ideal for use with tipping-bucket rain gauges, and can record tens of thousands of measurements and events.
![hobo pendant light logger manual hobo pendant light logger manual](https://www.fondriest.com/media/catalog/product/cache/32691bf1635b70786267ca53034a5d2d/o/n/onset_hoboware_pro.jpg)
The HOBO Pendant Event/Temp Data Logger is a rugged, weatherproof event logger with a 10-bit temperature sensor.